Jump to content

Wojtek Gdańsk

Beta Tester
 View Profile  See their activity

  • Posts

    93

  • Joined

  • Last visited

 Content Type 

Posts posted by Wojtek Gdańsk

  7. The Beta Autoslew

    in Software

    Posted · Edited by Wojtek Gdańsk

    Hello. Unfortunately for me the new version Autoslew DE axis can not find your Home Positions, and for this I came back to the previous version Autoslew .

     
     
    Wojtek.

  14. any advice on how to stop the humming and shuddering?

    in ASA DDM85, 100, 200, 500

    Posted

    Welcome. I DDM60 but I think the PID is the same as DDM85 . On my DDM is installed DDM C14HD but still copes with such a heavy burden . At the beginning I also had problems such as tremors DDM , it took me quite some time before the DDM started going to watch = ) . The first thing I did to DDM do not run in the tremor and no humming .

    1 ) balanced the DDM using the built- in autoslew electronic tool .

    2 ) I ran the auto-tuning PID - autoslew pre- configured PID but DDM is still not functioning as it should so the auto-tuning PID ran further manual tuning , and he tuned PID . As I wrote above, it took me a lot of time. Now DDM performs well .

    As for the filter axis RA and DE . I do not know with you but in my ED axis I rather high set PID parameters so that the axis of the DE from the filter I am very pleased. Unfortunately, the RA axis when I turned on the filter I can not quite high set of PID parameters - practically you do not hear any engine operating in the RA axis I PID parameters set to low ranges - I do not know if it's good . Are you also in the RA axis is a problem with the filter.

    Regards

    Wojtek .

  15. Servo Setup - Balance

    in ASA DDM85, 100, 200, 500

    Posted · Edited by Wojtek Gdańsk

    Welcome. Your problem of vibration and noise DDM 90% is caused by bad motor PID settings , you have to work a little bit in the PID settings . I am now on a business trip and I can not check on my DDM60 how PID may account for this anomaly engine but had the same problem as you. As for the noise filter axis RA - On my DDM60 is installed C14 HD and also in the axis of the RA I have a problem with this filter , I can not be set using the filter high PID parameters , this problem occurs only in the axis RA axis DE I do not have any problems with the filter can be set as high as the PID parameters . Some time ago I reported this problem to the company ASA , the company wrote back to me that I do not have to necessarily use the filter in the RA axis - admit that it is a little strange answer. I believe that if there is such a function as filters in the RA axis and the axis DE they should work without problems in both axes. I f the answer ASA is a bit strange . Luck in PID parameter settings .

    Regards , Wojtek

  16. OK3Z + Joystick

    in Tips & Tricks

    Posted · Edited by Wojtek Gdańsk


    Welcome. What should I do to Fokuser OK3Z work together with the joystick. I had problems with this so maybe someone handy video which shows what you need in Autoslew pozaznaczać to OK3Z began to work with the joystick. 

    1) You must have already installed the driver and software to OK3Z ACC. 

    2) Open the ACC and configure it correctly. 

    3) Confirm there are in the ACC operates fokuser. If it works correctly, close the ACC. 

    4) Start Autoslew and proceed as shown in the film. 

    Regards, Wojtek. 


     


  19. Problem Joystick OK3Z

    in ASA Focuser

    Posted

    Welcome. I bought this joystick which you use but unfortunately my OK3Z still does not work in joystick. Maybe it's the software control. My OK3Z is bought about a month ago so I have the latest software provided on the ASA after the Sept. 15, 2011. What software do you use ACC. Admittedly ASA I wrote (Dear Wojtek, 

    We do not support the focuser feature in Autoslew any more. So you need to use the software control for focusing. Unfortunately there is no joystick support in the ACC at the moment. 

    Sorry for the bad news. 

    Best regards,) 

     

    Regards, Wojtek.

  21. Problem Joystick OK3Z

    in ASA Focuser

    Posted

    Hello again. You write that you are using version 5.1.1.6 Autoslew, I'm using version 5.2.0.4 - the so-called Beta Tester. Even today I install on a laptop version of the general's son available on the ASA or 5.1.1.6. ACC program I have installed and guess? fully configured because in the ACC can move OK3Z no problem. Thank you for your help I am curious if joystick work 

    Regards, Wojtek

  23. Problem Joystick OK3Z

    in ASA Focuser

    Posted · Edited by Wojtek Gdańsk

    Are you sure that the joystick is in Autoslew for DDM85 and for OK3Z. That would be weird because Autoslew software is one for DDM60 and for DDM85. What version are you using to control Autoslew DDM85. 

     
    Regards, Wojtek

  24. Problem Joystick OK3Z

    in ASA Focuser

    Posted

    Hello again. I DDM60 and steer it using the joystick without a problem. Unfortunately OK3Z does not work with joystick. I wrote to the ASA today and got answer that for now OK3Z does not work with joystick but in the ACC this feature will soon be available. Thank you for your interest. 

     

    Regards, Wojtek

  25. Problem Joystick OK3Z

    in ASA Focuser

    Posted · Edited by Wojtek Gdańsk

    Welcome. Thank you for your prompt answer. I have installed the Google translator. I think you should understand how to write in English, how to solve the problem of control OK3Z joystick.. Vive FRANCJA.  :D

     

    Pozdrawiam, Wojtek.

×
×
  • Create New...